Things are progressing slowly with the new-to-us park model home here at Viewpoint Golf and RV Resort. So far, the process has been a matter of removal rather than move-in. Donna has been sorting through the things she plans to sell in the park-wide garage sale scheduled for Saturday, March 20th. Whatever doesn’t sell will be donated.

Donna also took down all of the window hangings – curtains, rods and whatnot. They were all dated and in need of replacement. I hauled it to the community dump here at the park. There was also a small knick-knack shelf that ran around the perimeter of the living room that she didn’t want. She hired a guy from the park to rip it out and dispose of it along with a cabinet above the bed.

We’ve had some great help from our friends and neighbors, Dick and Roxy Zarowny. Roxy has been helping Donna with some paint prep and color ideas. Dick took down a few light fixtures we’ll be replacing and he also filled in trim where the living room shelf was. Another neighbor, Sue Lines, has also been consulted about paint colors. We can’t thank them enough for their time and help.

I’ve moved a few items into the small shed/shop. I’ll need to get cracking on moving everything out of the trailer so we can sell it. That’ll be this weekend’s project. Yesterday, I went over to the house to spackle some holes left from curtain hardware and other wall hangings.

We had a change of plan on painting the interior. We got a quote from a painter here at the park and decided to hire the job out. In years past, I always tackled these jobs to avoid the expense of hiring someone, but I’m at a point in my life where I’d rather hire someone and be done with it. They will start masking everything and apply coverings tomorrow and should complete the job by the middle of next week – they won’t work on the weekend. Once that’s complete, we can start moving in.

I’ve mentioned a bit of an evolution in my kitchen duties – I’m learning kitchen knife skills and applying them to different recipes. Meanwhile, Donna has been utilizing the Weber grill more. One of my specialties is Japanese fried rice. I’ve been making it in a large skillet, but it wasn’t ideal. The skillet isn’t quite large enough and stirring while the rice fries results some of the ingredients escaping from the pan.

I decided I needed a wok. I looked around online and settled on a Yosukata carbon steel wok from Amazon. It has a flat spot on the bottom making it stable on the induction cooktop and carbon steel is ferrous and works great with induction. The name “carbon steel” is a misnomer. All steel contains iron and carbon.

After ordering this pan, I’ve been inundated with ads and click-bait for carbon steel kitchenware. Against my better judgement, I clicked on one that led to blog post about cookware – it was just a shill for certain products. The author was either horribly mis-informed or didn’t do any research at all. He started by saying carbon steel is great in the kitchen because it is a blend of “normal steel” and stainless steel. This is preposterous. First of all, what is “normal steel?”

As I said, all steel contains iron and carbon. From there, different alloying elements can be added. Most metallurgists agree that the addition of chromium in amounts exceeding 11% of the total weight constitute a stainless steel alloy. So-called carbon steel can be anything from very pure iron and carbon like that found in Hitachi Shirogami steel or can have additions like manganese, tungsten, vanadium and a host of other ingredients – but it wouldn’t be called carbon steel if it had more than 11% chromium – it would be called stainless. This is why I say the statement in the kitchen blog is preposterous.

Anyway, the wok is carbon steel and when properly seasoned – like cast iron – it’s nearly non-stick in use. The pan is made from thin material that heats up and cools down quickly and is much lighter than cast iron. It’s sizable – nearly 14 inches in diameter and four inches deep. Just right for fried rice.

Speaking of steel, Roxy mentioned to Donna that her old set of kitchen knives she keeps in their motorhome were in need of sharpening. So Donna asked me if I could sharpen them for her. It was a set of LC Germain knives. These knives were made in Japan in the 1970s and ’80s. They are stamped from a sheet of stainless steel and achieve their sharpness through the use of very thin blade material. To make the thin blades wear-resistant, they were heat-treated in a way that forms large, very hard carbides. I think the manufacturer wanted these knives to hold up in home kitchens where the user wouldn’t sharpen them or would maybe send them out to be sharpened by someone with a grinder once a year or so.

I don’t have a grinder and my Japanese knives are carbon steel with very fine grain structure, making them easy to sharpen. Therefore, my Japanese water stones are finer grades. These LC Germain knives should have been sharpened with a coarse stone to reset the edge, then refined on harder stones. I couldn’t find my Lansky coarse stone, so I had to use the Spyderco Sharpmaker which I only have medium and fine grit stones for. It took a lot of elbow grease to reach a useable edge on the knives. Hopefully, I’ll find the Lansky sharpener when I empty the trailer and can have another go at the LC Germain knives.

We drove out to Buckeye on Sunday to visit with my middle daughter, Jamie. Jamie is starting a home baking business specializing in cookies – it’s called OMG Cookies. Donna ordered two dozen cookies from her that she wanted for gifts to her tennis girlfriends here at Viewpoint. I gifted Jamie with the Yaxell Enso Japanese ko-bunka knife that got me started on the Japanese knife kick. We visited for a while, then made the drive back – it’s about 75 miles each way. In the air-conditioned Nissan Frontier, the trip was breeze.

The Frontier airbag saga continued. I was up early and off to the Nissan dealer in west Mesa to have the airbag module replaced and programmed on Monday. I waited there for four hours – good thing I brought a book to read. It didn’t solve the problem. They said the wiring harness needed to be replaced and said Sullivan Motors would be calling me to make arrangements.

Chris at Sullivan called me on Tuesday and said he was working on a solution. Then he called on Wednesday and asked if I could bring the truck to their shop at 8am on Thursday (today). He said the wiring harness was on backorder, but he thought they could repair it. I was skeptical , but I got up early and went there this morning. He had a different guy look at it this time. I sat and read for a while, then took a walk. When I got back, the truck was parked outside the shop. The guy located the break in the harness and repaired it! Hopefully, that’s the last time I’ll have to deal with it.

Time for some food talk. The fried rice in the wok photo went with a wild Alaskan salmon filet that Donna grilled perfectly.

I’ll add a couple more dinner plates from the last week. Donna made balsamic chicken and peppers served with home fries.

She also made a meal with leftover tri-tip from the weekend. She had me slice the tri-tip into thin slices along with mushrooms, onion and garlic. Then she cooked chickpea rotini pasta and made a version of classic beef stroganoff.

It was a delicious meal.

We’re looking forward to visit from my oldest daughter, Alana and her fiancé, Kevin this afternoon. We’ve had warm weather over the weekend and start of this week – it was in the 80s. Yesterday it cooled down and only reached 70 and today should be slightly cooler. It should be comfortable to sit outside in the sun while we catch up with them.

*Just so you know, if you use this link to shop on Amazon and decide to purchase anything, you pay the same price as usual and  I’ll earn a few pennies for the referral. It’ll go into the beer fund. Thanks!